Consolidated Statutes and Regulations
Consolidated Statutes
Consolidated Regulations
Annual Statutes and Regulations
Annual Statutes
Annual Regulations
Additional information
Québec Official Publisher
What’s new?
Information note
Policy of the Minister of Justice
Laws: Amendments
Laws: Provisions not in force
Laws: Provisions brought into force
Annual Statutes: PDF versions since 1996
Regulations: Amendments
Annual Regulations: PDF versions since 1996
Court Decisions
S-2.1, r. 4 - Safety Code for the construction industry
Section 3.10.8
Disposition versions
3.10.8. Vehicle-mounted aerial device:
(1) A vehicle-mounted aerial device manufactured before 1 January 2000 shall meet one of the following requirements:
(a) comply with CSA Standard C225-1976 Vehicle-Mounted Aerial Devices;
(b) comply with ANSI Standard A92.2-1979 Vehicle-Mounted Elevating and Rotating Aerial Devices and be submitted to non-destructive testing of load bearing parts by a certified body before 1 January 2000; or
(c) comply with ANSI/SIA Standard A92.2-1990 Vehicle-Mounted Elevating and Rotating Aerial Devices.
(2) A vehicle-mounted aerial device manufactured on or after 1 January 2000 shall meet one of the following requirements:
(a) comply with CAN/CSA Standard C225-M88 Vehicle-Mounted Aerial Devices; or
(b) comply with ANSI/SIA Standard A-92.2-1990 Vehicle-Mounted Elevating and Rotating Aerial Devices and have been manufactured by an enterprise certified in compliance with ISO 9001.
(3) A worker in an aerial device must wear a safety harness secured by a fall arrest connecting device to an anchorage system provided by the device’s manufacturer or, failing that, to an anchorage system complying with section 2.10.15. The harness and fall arrest connecting device must comply with section 2.10.12.
(4) Mobile cranes are not governed by this section.
(5) For the purposes of this section,
“certified organization” means an organization certified by the Canadian Welding Bureau to the requirements of CSA Standard W178.1-1996 Certification of Welding Inspection Organizations;
“load bearing device” means a device that carries or supports loads relative to the use of an aerial device;
“non-destructive testing” means testing, other than visual, carried out and interpreted by a Level II inspector certified by the Canadian General Standards Board in compliance with the certification standards for personnel assigned to non-destructive inspection of materials.
3.10.8. Vehicle-mounted aerial device:
(1) A vehicle-mounted aerial device manufactured before 1 January 2000 shall meet one of the following requirements:
(a) comply with CSA Standard C225-1976 Vehicle-Mounted Aerial Devices;
(b) comply with ANSI Standard A92.2-1979 Vehicle-Mounted Elevating and Rotating Aerial Devices and be submitted to non-destructive testing of load bearing parts by a certified body before 1 January 2000; or
(c) comply with ANSI/SIA Standard A92.2-1990 Vehicle-Mounted Elevating and Rotating Aerial Devices.
(2) A vehicle-mounted aerial device manufactured on or after 1 January 2000 shall meet one of the following requirements:
(a) comply with CAN/CSA Standard C225-M88 Vehicle-Mounted Aerial Devices; or
(b) comply with ANSI/SIA Standard A-92.2-1990 Vehicle-Mounted Elevating and Rotating Aerial Devices and have been manufactured by an enterprise certified in compliance with ISO 9001.
(3) A worker in an aerial device must wear a safety harness complying with CAN/CSA Standard Z259.10-M90 Full Body Harnesses and be equipped with a lanyard attached to a point of anchorage independent of the aerial device.
(4) Mobile cranes are not governed by this section.
(5) For the purposes of this section,
“certified organization” means an organization certified by the Canadian Welding Bureau to the requirements of CSA Standard W178.1-1996 Certification of Welding Inspection Organizations;
“load bearing device” means a device that carries or supports loads relative to the use of an aerial device;
“non-destructive testing” means testing, other than visual, carried out and interpreted by a Level II inspector certified by the Canadian General Standards Board in compliance with the certification standards for personnel assigned to non-destructive inspection of materials.
